THEJO TC-310 Cold Adhesive – Medium Cure Inflammable Adhesive

THEJO TC-310 Cold Adhesive – Medium Cure Inflammable Adhesive

THEJO TC-310 Cold Adhesive is a two-component, medium-cure cold bonding adhesive system developed for industrial rubber bonding applications. It is part of THEJO’s TEZ cold splicing solutions, which are designed for conveyor belt splicing, pulley lagging and rubber repair work.

THEJO TC-310 Cold Adhesive is used with compatible HC hardener compounds. The adhesive system is designed for applications where a medium curing rate and good bonding strength are required. Correct surface preparation, mixing, application and curing procedures are essential to achieve a suitable bond.

This product is intended for industrial use by maintenance teams, conveyor service providers, workshops and other professionals involved in conveyor belt maintenance and rubber bonding.

Key Features of THEJO TC-310 Cold Adhesive

• Two-component system: Requires compatible HC hardener before use.
• Medium cure rate: Designed for applications where a medium curing rate is appropriate.
• Industrial rubber bonding: Suitable for specified rubber-to-rubber and rubber-to-metal bonding applications.
• Conveyor belt maintenance: Used for conveyor belt splicing and repairs involving fabric-ply belts.
• Pulley lagging: Suitable for specified conveyor pulley lagging applications.
• Cold bonding process: Designed for cold bonding applications without relying on a hot vulcanising process.
• Industrial application: Intended for conveyor maintenance, repair and related rubber bonding work.

The actual bond performance depends on substrate condition, preparation, mixing ratio, application technique and curing conditions. Follow the current manufacturer’s technical documentation for the exact system.

Applications of THEJO TC-310 Cold Adhesive

Conveyor Belt Splicing

THEJO TC-310 is designed for conveyor belt splicing and repair applications. The manufacturer’s product data identifies fabric-ply conveyor belts made with nylon, rayon, polyester and cotton reinforcement as suitable application areas.

Correct preparation of the belt ends and adherence to the specified bonding procedure are important for achieving a reliable splice.

Conveyor Pulley Lagging

The adhesive system can be used for suitable conveyor pulley lagging work, including bonding compatible rubber lagging materials to prepared metal pulley surfaces. Surface preparation and the specified primer system should follow the manufacturer’s instructions.

Rubber-to-Metal Bonding

THEJO TC-310 is suitable for specified rubber-to-metal bonding applications. The manufacturer identifies TPR-1400 as a primer used in its adhesive system to enhance rubber-to-metal bond strength. Confirm the correct primer and process for the application before use.

Rubber-to-Rubber Bonding

The product is designed for compatible rubber bonding applications, including conveyor belt repairs and splicing. Confirm compatibility with the specific rubber compound and follow the recommended preparation procedure.

Industrial Conveyor Maintenance

Maintenance contractors and industrial service teams may use THEJO TC-310 for suitable cold bonding work on conveyor systems in industrial facilities. Application selection should account for belt construction, operating loads, environmental conditions and the manufacturer’s requirements.

How the Two-Component Adhesive System Works

THEJO TC-310 is not a single-component adhesive that can be applied directly without preparation. It is a two-component system that must be mixed with the specified HC hardener compound before use.

The manufacturer’s product data identifies a pot life of approximately 2–3 hours at 23°C for the mixed solution. This is a typical published value, not a guarantee under all working conditions. Temperature, mixing accuracy and application conditions can affect the usable working time.

Prepare only the amount that can be applied within the specified pot life. Do not use material that has exceeded its permitted working time or shows signs of unsuitable condition.

Application Guidelines

1. Prepare the substrate: Remove contamination, dirt, oil, grease and loose material using the manufacturer’s approved preparation procedure.
2. Prepare the adhesive system: Mix TC-310 with the compatible HC hardener according to the current technical instructions. Do not guess the mixing ratio.
3. Apply the specified primer: Where required, use the recommended primer, such as TPR-1400 for the relevant rubber-to-metal application.
4. Apply the adhesive: Follow the manufacturer’s instructions for coating, coverage, drying and assembly.
5. Complete the bonding process: Join the prepared surfaces and follow the specified pressure, alignment and curing procedure for the particular repair or splice.
6. Allow sufficient curing time: Do not return the conveyor or equipment to service until the manufacturer’s requirements have been met.

These are general process stages. The current manufacturer’s application instructions must take precedence for exact quantities, coating sequence, drying times, pressure requirements and curing conditions.

Technical Information

The manufacturer’s technical data describes TC-310 as a liquid adhesive system containing a polymeric mixture and aromatic and aliphatic hydrocarbons. The published product sheet lists a greenish-yellow appearance, a shelf life of at least 12 months when stored below 20°C under the stated conditions, and a mixed-system pot life of approximately 2–3 hours at 23°C.

The solvent is flammable. Storage, handling, ventilation and personal protective equipment must follow the applicable safety data sheet. Keep the product away from ignition sources and store it in a cool, dry place, protected from direct sunlight and moisture as instructed by the manufacturer.

Buy THEJO TC-310 Cold Adhesive from Technosteer Online

Technosteer Online supplies industrial products for maintenance teams, workshops, conveyor service providers and commercial buyers.

THEJO TC-310 Cold Adhesive is an option for suitable conveyor belt splicing, pulley lagging and rubber bonding applications that require a medium-cure, two-component adhesive system.

Before ordering, confirm the required quantity, compatible HC hardener, primer requirements and application suitability. For bulk requirements or commercial enquiries, contact Technosteer Online to check product availability.

For product-specific technical details, consult the official manufacturer’s documentation and current safety data sheet.